--- Go to the Woodblock.com Front Page ---

View unanswered posts | View active topics It is currently Wed Feb 21, 2018 8:37 pm



Post new topic Reply to topic  [ 8 posts ] 
My First, um, butchered block 
Author Message

Joined: Tue Jun 14, 2011 11:20 pm
Posts: 18
Location: San Francisco, CA
Post My First, um, butchered block
well, in the main, i believe i've butchered this first block.

* clearly, the design is far too large for the block (10cm x 15cm)
* used a sketch i had pasted down before i bought YFP
* block is from a kinokuniya in San Francisco's Japantown
* tried looking over back of right hand (with right-handed hangitoh) to cut the lines
* sliced right through my design repeatedly
* probably cutting too deep in some places
* couldn't find much use for a bullnose or small flat chisel
* mostly used a narrow u-gouge
* found myself prying down, against, and _away_ from the design
(this _must_ be a bad idea, as it stresses the design area)
* had trouble keeping the u-gouge sharp
* cross grain cutting was treacherous, kept cracking the design
* the wood split and chipped through the design frequently
* couldn't see any way to cut the finer details
* tried to cut the registration with a 21mm flat chisel

i'm not sure i can get a good impression from it, but i'll try!
obviously, i have a long way to go…

any comments or suggestions would be most welcome.

Steve


Attachments:
IMG_0242.JPG
IMG_0242.JPG [ 225.22 KiB | Viewed 23436 times ]


Last edited by Steve Sisney on Fri Jun 17, 2011 5:31 am, edited 2 times in total.

Fri Jun 17, 2011 5:21 am
Profile E-mail

Joined: Tue Jun 14, 2011 11:20 pm
Posts: 18
Location: San Francisco, CA
Post Re: My First, um, butchered block
the tools i used... attached.


Attachments:
IMG_0243.JPG
IMG_0243.JPG [ 106.46 KiB | Viewed 23435 times ]
Fri Jun 17, 2011 5:23 am
Profile E-mail

Joined: Tue Jun 14, 2011 11:20 pm
Posts: 18
Location: San Francisco, CA
Post Re: My First, um, butchered block
another view of the carnage...


Attachments:
IMG_0244.JPG
IMG_0244.JPG [ 150.06 KiB | Viewed 23435 times ]
Fri Jun 17, 2011 5:25 am
Profile E-mail

Joined: Tue Jun 14, 2011 11:20 pm
Posts: 18
Location: San Francisco, CA
Post Re: My First, um, butchered block
the gory details...


Attachments:
IMG_0245.JPG
IMG_0245.JPG [ 134.54 KiB | Viewed 23435 times ]
Fri Jun 17, 2011 5:26 am
Profile E-mail

Joined: Tue Jun 14, 2011 11:20 pm
Posts: 18
Location: San Francisco, CA
Post Re: My First, um, butchered block
the block and design. i transferred it to tracing paper with a "brush" artist's pen, and pasted the tracing paper directly to the block.


Attachments:
IMG_0247.JPG
IMG_0247.JPG [ 101.46 KiB | Viewed 23435 times ]
Fri Jun 17, 2011 5:38 am
Profile E-mail
Site Admin
User avatar

Joined: Mon Aug 31, 2009 2:30 pm
Posts: 194
Location: Tokyo, Japan
Post Re: My First, um, butchered block
Somebody's having fun!

Can I toss in a couple of points? You have certainly taken on a fair challenge for a 'first' print - all those fine lines, especially involving small circular shapes. That's about the most difficult carving there is ...

In general, I think you are digging too deeply. When the lines are fairly close together, there is little danger of the paper sagging down between them at printing time, and there is thus no necessity to excavate quite so far down. You said you couldn't find much use for the flat chisel ... but this is exactly what it is used for. Score your outlines, use your u-gouges to scoop out some of the waste at a distance from the lines, then use the flat chisel to 'level off' the area up to the lines ...

Also, you do have a bit of an issue with sharpening! When the left-over wood has a lot of 'fuzzyness' along the length of a scooped out area, it's an indication of a dull tool. Do you have a little stone to rub the gouges over now and then?

But anyway, this one looks like a lot of fun! What's the plan for colour blocks?


Fri Jun 17, 2011 8:57 am
Profile E-mail WWW

Joined: Tue Jun 14, 2011 11:20 pm
Posts: 18
Location: San Francisco, CA
Post Re: My First, um, butchered block
thanks so much for your "points" Bull-san.

i'll try to use the gouges, then the flat chisel to level out more shallow areas around the scoring on the next blocks.

i just picked up a medium (#1000) stone (pictured) with troughs for my u-gouges, but they don't fit perfectly. i'll do my best...

the only plan i have for color blocks is "red and green". maybe (pale) red octopus on a (pale) green field in alternating bokashi (green from the top of the field, red from the bottom of the octopus)?

i may carve out some void (un-printed?) motif in the field or the skin of the octopus. i thought i would sketch on my key block tests before deciding.

if i can salvage this design, i'd like it to look as "ukiyo-e" as possible.

Steve


Attachments:
IMG_0241.JPG
IMG_0241.JPG [ 66.38 KiB | Viewed 23421 times ]
Fri Jun 17, 2011 6:14 pm
Profile E-mail

Joined: Tue Jun 14, 2011 11:20 pm
Posts: 18
Location: San Francisco, CA
Post Re: My First, um, butchered block
this is a little more promising (pictured). i sharpened my tools, cleared everything but the design and registration, and tried to level things out. after washing it, i can see more clearly how jagged my lines are. i think i'll try some test prints before i start hacking at it again though.

Steve


Attachments:
IMG_0319.jpg
IMG_0319.jpg [ 161.58 KiB | Viewed 23411 times ]
Sun Jun 19, 2011 12:36 am
Profile E-mail
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 8 posts ] 


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group.
Forum style by Vjacheslav Trushkin for Free Forums/DivisionCore.